Change IPC Firmware Lincoln MKZ to Mondeo MK5/Fusion

[fordsmaxtcdi]

the files are in the wrong order and also the can-bus is wrong

2021-04-08 (2).png
as this ??

right,
enable SLEEP all modules and use a car battery charger of 8 -.... amps

[polofox]

2021-04-08 (2).png
as this ??

right,
enable SLEEP all modules and use a car battery charger of 8 -.... amps

Thanks very much ,we will try it again

[fordsmaxtcdi]

right,
enable SLEEP all modules and use a car battery charger of 8 -.... amps

Thanks very much ,we will try it again

For 2018 Fusion/Mondeo:
(Bootloader): EJ7T-14C025-AA
JS7T-14C026-AJB
JS7T-14C026-BJB
JS7T-14C088-AJB
JS7T-14C088-BJB
- Firmware Build Date: October 30, 2017
firmware has the thick blue needles for gauges - digital speedometer moved to center

[polofox]

Thanks very much ,we will try it again

For 2018 Fusion/Mondeo:
(Bootloader): EJ7T-14C025-AA
JS7T-14C026-AJB
JS7T-14C026-BJB
JS7T-14C088-AJB
JS7T-14C088-BJB
- Firmware Build Date: October 30, 2017
firmware has the thick blue needles for gauges - digital speedometer moved to center

My Car is Mondeo 2015 Titanium cd391,is ok?

[fordsmaxtcdi]

yes but if you load the IPC configuration data, select the correct direct config type according to the module number

[polofox]

yes but if you load the IPC configuration data, select the correct direct config type according to the module number

but all vbf has "Set new address failed."
my hardware is DP5T-14F094-CB

2021-04-08 (5).png

2021-04-08 (4).png

[fordsmaxtcdi]

wrong order and HW=F113

123.png

[polofox]

wrong order and HW=F113
123.png

2021-04-09 (1).png

Is that the right order?

[fordsmaxtcdi]

yes try

[polofox]

yes try

00:00:00:509: Requesting hardware parts number...
00:00:00:767: F113 (HW) part number: DS7T-10849-CJR
00:00:00:769: F188 (SW) part number: DS7T-14C026-DJT
00:00:00:770: Loading and prepare database...
00:00:05:168: Searching for SEED keys...
00:00:05:170: SEED Keys found.
00:00:05:176: Programming mode OK!
00:00:06:179: Requesting protected mode...
00:00:06:190: Protected mode granted!
00:00:06:341: Loading Secondary Bootloader...
00:00:16:226: Secondary Bootloader successfully loaded and initialized.
00:00:16:535: Erasing flash...
00:00:16:537: Erasing flash block 1 from 2 ...
00:00:16:547: Erase Operation failed.
00:00:17:550: Failed to programming flash! Error: Request Out Of Range [0x31]
00:00:00:506: Requesting hardware parts number...
00:00:00:764: F113 (HW) part number: DS7T-10849-CJR
00:00:00:769: F188 (SW) part number: DS7T-14C026-DJT
00:00:00:779: Loading and prepare database...
00:00:05:017: Searching for SEED keys...
00:00:05:022: SEED Keys found.
00:00:05:038: Programming mode OK!
00:00:06:048: Requesting protected mode...
00:00:06:060: Protected mode granted!
00:00:06:212: Loading Secondary Bootloader...
00:00:16:102: Secondary Bootloader successfully loaded and initialized.
00:00:16:412: Erasing flash...
00:00:16:415: Erasing flash block 1 from 2 ...
00:00:16:421: Erase Operation failed.
00:00:17:424: Failed to programming flash! Error: Request Out Of Range [0x31】



It's still the same mistake.

2021-04-09 (2).png

[as2222us]

I assume that your IPC has only 512kb ROM. It must be an very old IPC.

[fordsmaxtcdi]

IPC photo

123.png

[polofox]

IPC photo
123.png

2021-04-09 (3).png

[fordsmaxtcdi]

Electronic instrument cluster photo
and new ucds ver.
viewtopic.php?f=3&t=4

[polofox]

Electronic instrument cluster photo

as this?

UCDS IS V2.0.007.003