Change IPC Firmware Lincoln MKZ to Mondeo MK5/Fusion

[janel]

downgrade to JS7T.
KS7T only works with the new IPMA (JG9T-19H406-xx) as far as I know.

[rabei3]

Hi All
Can i install IPC From Ford Explorer 17 To Explorer 14 limited

[DanMc85]

Hi All
Can i install IPC From Ford Explorer 17 To Explorer 14 limited

no... PATS system in IPC vs BCM... CEGA 1.2 vs 1.3

[NavigatorV8]

Hi All
Can i install IPC From Ford Explorer 17 To Explorer 14 limited

no... PATS system in IPC vs BCM... CEGA 1.2 vs 1.3

I plan to do the same, figured out, after exchange of 2 wires at IPC plug, it will actually alive but it will not work properly.
Absolute no upgrade possible?

[Diamondear]

The KS7T- & LS7T- calibrations for the IPC module work perfectly with IPMA calibration FS7T-14G019-SJ or higher.


Update IPMA Module:

DA5T-14G021-BA - Bootloader
FS7T-14G019-SJ
FS7T-14G024-SJ
HS7T-14G082-CB
HS7T-14G081-CB


Sequence with VBF Loader:

1. SBL DA5T-14G021-BA
+ FS7T-14G019-SJ
+ FS7T-14G024-SJ

2. SBL DA5T-14G021-BA
+ HS7T-14G082-CB

3. SBL DA5T-14G021-BA
+ HS7T-14G081-CB

[AmigaSurfer]

The IPMA software FS7T-14G019-SJ is for the ECU Core Assembly Number FS7T-14G025-Sx for cars with Collision Mitigation System. Does this software work on the ECU Core Assembly Number DS7T-14G025-Ex built in cars without Collision Mitigation System, too?

[rob180]

The KS7T- & LS7T- calibrations for the IPC module work perfectly with IPMA calibration FS7T-14G019-SJ or higher.


Update IPMA Module:

DA5T-14G021-BA - Bootloader
FS7T-14G019-SJ
FS7T-14G024-SJ
HS7T-14G082-CB
HS7T-14G081-CB


Sequence with VBF Loader:

1. SBL DA5T-14G021-BA
+ FS7T-14G019-SJ
+ FS7T-14G024-SJ

2. SBL DA5T-14G021-BA
+ HS7T-14G082-CB

3. SBL DA5T-14G021-BA
+ HS7T-14G081-CB

Can you update all the VBF files at the same time? like the following....

Capture.PNG

[zhuory-1]

I found mkx 2018 IPMA firmware is FT4T-14G082-ME, can I update with IPMA Module: DA5T-14G021-BA - Bootloader FS7T-14G019-SJ FS7T-14G024-SJ HS7T-14G082-CB HS7T-14G081-CB?Thank you very much!

[zhuory-1]

DanMc， can I update with FT4T-14G082-ME for U0198?

[adsvoo]

I prefer this option, so I no longer gonna update my firmware

[pronosoft]

The
auto high beam is still working, only the white auto high beam telltale is gone and I don't miss this telltale. The blue high beam telltale is still visible.

[pronosoft]

I prefer
this option, so I no longer gonna update my firmware

[mayurreddy]

I am curious since you are messing with a MKZ cluster on Mondeo... does it default to MPH every startup or does it keep your preference of KM stored? Not sure if this is stored in EEPROM or if it is As-Built Data controlled.

I attached two photo's of the MKZ cluster with an american and an german eeprom content in it. You can clearly see that the mph versus km as well as C---H versus 60..120 and E...F versus 0...1 is controlled by the eeprom

Mondeo_DE_eeprom.JPG

MKZ US eeprom.JPG

Can you please share the MKZ eeprom file .
thanks in advance

[AmigaSurfer]

I prefer this option, so I no longer gonna update my firmware

You can get the white AutoHighBeam Telltale back with IPC firmware KS7T-14C026-AJD and higher by changing IPC DE08 "Auto High Beam Telltale" from "disabled" to "IPMA".

BTW, there is a call-back 20P06 for Mondeo MK5 equipped with IPC firmware JS7T-14C026-AJB and KS7T-14C026-AJD. If you have updated an IPC with older firmware to one of this firmwares, I suggest to make this change by hand.
IPC DE06 "(not used) *DO NOT USE (AutoHigh Beam Telltale)" must be changed from Disabled to Enabled. It's bit 30 in IPC DE06.

[peterpro]

Thank's Amiga for this info!
i'm not a noob in UCDS programming but some more info's are welcome
You say: You can get the white AutoHighBeam Telltale back with IPC firmware KS7T-14C026-AJD and higher by changing IPC DE08 "Auto High Beam Telltale" from "disabled" to "IPMA".
This is possible only in UCDS with KS7T-B** direct config menu (with should be ok having calibration KS7T-14C026-BJD), if you select the other options of direct configuration (KS7T-J* and KS7T-G*) this selection is not present in DE08!
BUT you say either: BTW, there is a call-back 20P06 for Mondeo MK5 equipped with IPC firmware JS7T-14C026-AJB and KS7T-14C026-AJD. If you have updated an IPC with older firmware to one of this firmwares, I suggest to make this change by hand.
IPC DE06 "(not used) *DO NOT USE (AutoHigh Beam Telltale)" must be changed from Disabled to Enabled. It's bit 30 in IPC DE06
Here is the strange....this voice is present only in DE06 of all IPC (KS7T-J* and KS7T-G*) but not in KS7T-B**, that in fact i must use to edit the other option. So something confusing here... attached images
With UCDS how did you wrote this values in IPC?
And last....upgraded with success from GS7T-14C026-AJE to KS7T-14C026-AJD, all went ok, ipma already to FS7T-14G019-SJ, traffic sign works, but i loose the driver alert graphics system. I have the option ticked in Assistance menu of IPC (tried to enable/disable from there), but in old calibration there was some graphics with the cup of coffee that was grey under 65km/h and then got colored over that speed. If you want to check manually the driver alert status, in the last settings menu (vehicle or display... i cannot remember exactly) you could pump that graphics. Now is not visible any more and even trying to zig-zag during motion did not engaged the graphic alert itself that before was prompted! i tried to drive for 400km over 65km/h but still no graphics. traffic sign and lane assist are working as expected. Some tips?
Thanks a lot!